Before the lengthy winter started, I noticed my newly purchased camper got rotten moldy hardwood sections on 3 out of the 4 vertical edges of the roofing. I invested all wintertime thinking about it and reading numerous of the roof repair articles right here on PUX. Today my dad and I finally started tearing into the problem sections. In the finish, I plan on changing the front side, drivers side, and rear sections of the roof. The best and door side appear great.

View and Download Livin Lite Truck Camper owner's manual online. Bookmark Manual will be automatically added to 'My Manuals' Print this. Camplite TABLE OF. 2000 Camplite 2408 CLICKCAMPERS. Unsubscribe from CLICKCAMPERS? Cancel Unsubscribe. 1999 camplite sl by damon pop up - Duration: 7:14.

There's a plot of dark timber in the back of the door side, but it's not mushy or moldy like the relaxation, so I'm departing it only. So far for one evening's work, we obtained the front side piece of hardwood removed and scraped many of the staying wood laminate off the back of the distinctive roof plastic material. I've connected some images of the front side panel restoration so far. I program on replacing the hardwood with something like marine quality plywood and a layer of essential oil based primer/waterproofer. Ideally the primer will become overkill since I'll seal everything up the method it should have been recently in the very first place and no drinking water will obtain to the hardwood any more.

In any case, it's heading pretty great so much. I do have a couple questions about replacement unit material. Will anyone understand if and whére i can get the plastic material put that addresses all the screws in the metallic trimming that brings together the level roofing and vertical sides? Also, I'd including to replace the close off between the roof and entire body, but I'm not certain If I'll become able to find something to slide into that station in the light weight aluminum. Any recommendations for where to discover these items would end up being greatly appreciated. I'll article more pics and improvements as they are usually completed.

Front bunk extended and vinyl fabric dropped in order to access front cell of roof: Front side wood board. Totally shot: « Last Edit: April 01, 2010, 09:27:48 evening by CampinYEAHCampin » Logged. Just a several more pictures: Doesn't appearance too bad: Small worse on this end, but as you can notice from the image in the prior posting, the whole item of solid wood was shot: Plastic material textured roofing material with simply because much of the hardwood veneer scraped off the back. You can find how good the roof wood on best will be in this image.

It'beds simply the base edges where all the water arrives in through the Plenty of screw openings and there's no whére for it tó pipe from the metal edge covering the solid wood: « Final Edit: Apr 01, 2010, 09:30:32 pm by CampinYEAHCampin » Logged. Good situations for certain! That plastic cut you're after is definitely readily obtainable from most all RV parts areas. You'll need to tell them the size and color you would like, and how several foot of it you need. If the rubber weather burning is nevertheless smooth and fine, re-use it.

In any other case, if the company is still in business, probably you can order some from them. Chances are good that they make use of an sector standard steel trim and weatherstripping, só you can most likely discover the appropriate stuff if you're willing to quest. The various other option is to go to an automotive bodyshop offer store. They'll have books displaying the stuff that they can get in mass.

I had to change all the roof edges on my Damon too. I just used metal round head screws for the cut and produced sure it has been sealed well with a higher quality caulk. The hardest component for me had been lining up the raise parts seeing the real wood was completely rotted on one corner. I also got a hard period with the curve on one side because the timber was actually bad so not very much for a design template. BTW, some of the raise components on this van seem to flex on the bumper finish where it't adjustable.

This makes it out of modification and in my situation I finished up with component of the raise mechanism breaking because my FIL tried to pressure it up higher than it permitted. It was a easy restoration and I finished up béefing it up but simply something to watch out for. Thanks a lot for revealing PupInNH2.

I'meters also making use of a great silicon caulk in the trim channels mainly because nicely as priming the solid wood with an essential oil centered primer to hopefully maintain any dampness that could get to subjected places from affecting it. I'm worried about the curved edges also. The solid wood is pretty much mulch behind the textured exterior plastic material so I possibly received't possess a template to work from either. Can you use the plastic for a design template? We've only performed the top and back so considerably, and they're right pieces therefore not as tricky. I'll keep the raise adjustment concern in brain. Good to know.

I don't even know how to alter it! Got any pointers for me? I possess the manuaI, but dón't keep in mind seeing anything about the lift adjustment in there. If you have got any info or assets for the damon, make sure you talk about.

I wear't appear to see much about them anywhere. The finishes were easy except for obtaining the covering to sit down back lower.

I believe I do use the side covering but needed to take away a little bit because I believe it was a bit larger into the metal items. I judged as very best I could from the side that the real wood was relatively intact and the cover.

I believe I had to use 2 parts of plywood to obtain the size (container can be over 12 feet lengthy) and used Luaun balance at the articulation for one aspect and a steel item on the reverse aspect. I glued and surroundings stapled them together.

As for the lift system, it is usually a regular type that provides cables pressing spring suspensions to the sides. It's known as the 'Goshen lift system', you can see it right here: It't adjusted correctly if when all the way up you cannot force the top or back again up even more than the other from inside of. Appear under the rear and you'll observe the cable wrap around a puIley. The pulley is definitely connected with an flexible threaded pole. The installation point can be what curved on quarry so I added a piece of angle metal. Shawn, I am interested if you know where I can obtain a duplicate of the manuaI for the 1996 Camplite 2208 Beds?

My spouse and I simply bought one and are operating on a few 'fixes'. I do article this in another blog post particular to guides but thought I'd talk to you since you have the precise same design. It appears like you've had a bit of enjoyment with yours; I'm considering including Air conditioning unit (this winter; after our final few vacations) and read through someplace that this one might have the necessary framework for it. Thanks a lot in progress for your time. Cheers, - Jobe Logged. If I got this correct because yours is usually various from my stárcraft.

When you proceed to put the trim on make use of putty. After that place the trim on and fasten that with a robertson mess (rectangular mind) either reddish colored or green depending on the quantity of space you have got for the circular head and after that put your fresh vinyl cover up that film negatives in the sales channel. The exact same with attatching the track on the bottom part side of your cover that the seal slides into to meat the body, I used round robertson screws (natural types) and the close off slid right over it. Many RV areas will obtain you new seal. Niagara movie trailer got me the identical lid seal for my 74' for much less after that 30 dollars. Robertson anchoring screws are catergorized by colour. Black, Red, Environment friendly and Teal with black being the largest and the deal with of the screwdriver is usually coresponding colour.

The screws are stainless in colour. Phillips anchoring screws will not allow you create it tough to not really tighten sufficiently because of screw car owner slippage. I wish this assists.

Hi there Jobe, I'michael not certain where you could obtain an actual manuaI, but if yóu would including I can deliver you a pdf check of my manual. I think the roofing provides the proper wires and support for an air conditioner. Mine even has a wall plate best inside the door that is supposedly where you link the wires or a thérmostat or something. l haven't appeared at it too closely. I just went with a transportable A/G unit rather of installing a real Mobile home one on the roofing. It was just about $300.00 and is definitely 11,000 btu. I found that had been about a third of the cost for a roof build one.

We just bought a utilized (and slightly mistreated) Camplite and are searching for the manual. It offers two full bunks and a dinette slip away, which makes it just plain huge within. It'beds going to require a lot of work (where to start?). The seams on the roof sides had been leaking, which rotted somé of the timber on the edges of the best. Mice obtained in and chewed the vinyl - cushions are ok though! Windows vista 32-bit. We got the canvas away and today ants are showing up on the outdoors. What's the best way to obtain rid of thése buggers?

We'vé bombed it ánd put some Tero baits out. Fridge works. A/G runs cold. With some shoulder grease I believe that this can be a great van. Anyone tackle a project like this?